Barbell Jump Squat
- Secondary muscles
- Quads, Hamstrings, Calves
- Body part
- Upper Legs
- Position
- Standing
- Laterality
- Bilateral (both sides together)
- Category
- Plyometrics
Track this exercise in SetGrip — no account needed
Loading a jump changes the goal: with a bar on your back you are training rate of force, not jump height, so keep the load around 20-30 percent of your squat max and move it fast. Sets of 3-5 explosive reps work best - end the set as soon as bar speed visibly drops.
How to do the Barbell Jump Squat
- Start by standing with your feet shoulder-width apart, holding a barbell across your upper back.
- Lower your body into a squat position by bending your knees and pushing your hips back.
- Once you reach the bottom of the squat, explode upwards by jumping off the ground.
- As you jump, extend your hips, knees, and ankles, pushing through your toes.
- Land softly back into the squat position and immediately repeat the movement for the desired number of repetitions.
Tip: Screw the feet into the floor and spread it apart to keep the knees out and the arch of the foot from collapsing.
Muscles worked
Primary
Glutes · Legs
The glutes extend the hip on the way up and take more of the load the deeper you go and the wider your stance.
Secondary
- Quads — The quads extend the knee and drive you out of the bottom, and front squats and close stance variations put more on them.
- Hamstrings
- Calves
Common mistakes
- Knees caving inward — push the knees out over the toes on the way up, especially out of the bottom where they most want to collapse.
- Hips shooting up first — if the hips rise faster than the chest on the way up, you turn the squat into a good morning; drive the chest and hips up together.
- Cutting the depth — get the hip crease below the top of the knee on every rep unless mobility genuinely stops you, in which case work on it.
- Losing the brace — take a big breath into the belly before each rep and hold it through the sticking point, then exhale on the way up.
Sets, reps and where it fits
| Goal | Sets × reps | Rest |
|---|---|---|
| Power | 3–5 × 3–5 | 90–120 s |
| Conditioning | 3 × 8–12 | 60 s |
Squats go first in a lower body session when you are freshest. Follow them with Romanian deadlifts or leg press, or superset lighter sets with pull-ups to use the same rack.
Variations and alternatives
Similar exercises
Without barbell
Easier and harder
Frequently asked questions
What muscles does the Barbell Jump Squat work?
The Barbell Jump Squat primarily works the glutes. It also involves the quads, hamstrings and calves, which assist the movement and stabilise the joints.
Is the Barbell Jump Squat good for beginners?
Not as a starting point. The Barbell Jump Squat is rated advanced because it demands strength, mobility or coordination that takes time to build. Beginners should work up to it through the easier variations listed on this page.
What can I do instead of the Barbell Jump Squat?
If you cannot do the Barbell Jump Squat, try the Jump Squat, the Hands to Floor Jump Squat or the Dumbbell Plyometric Squat. Each of them trains the glutes through a similar movement, so you can swap them in without changing the rest of the workout.
How many sets and reps should I do?
It depends on your goal. For the Barbell Jump Squat, a sensible starting point is power: 3–5 × 3–5 with 90–120 s rest; conditioning: 3 × 8–12 with 60 s rest. Do it first in the session while you are fresh. Quality of each rep matters more than the count.
Track the Barbell Jump Squat in SetGrip
All 1,100+ exercises with animations are in the app. No account, no sign-up — your data stays on your iPhone. Works with Apple Watch.
More exercises
Exercise data and animations are licensed ExerciseDB content used in SetGrip. This page is for general information and is not medical or coaching advice.