Bench Hip Extension
- Primary muscleGlutes
- EquipmentBodyweight
- DifficultyBeginner
- TypeCompound · Hip-dominant
- Secondary muscles
- Hamstrings
- Body part
- Upper Legs
- Position
- Standing
- Laterality
- Bilateral (both sides together)
- Category
- Strength
Track this exercise in SetGrip — no account needed
Bracing your upper back on a bench raises the pivot point above the floor, so the hips travel through a longer arc than a floor bridge before the body lines out from knees to shoulders. Unloaded, it is the pattern rehearsal for a barbell hip thrust - same setup, same lockout, no bar to manage.
How to do the Bench Hip Extension
- Sit on a bench with your back against the bench and your feet flat on the ground.
- Place your hands on the bench for support.
- Engage your glutes and hamstrings, then lift your hips off the bench until your body forms a straight line from your knees to your shoulders.
- Pause for a moment at the top, then slowly lower your hips back down to the starting position.
- Repeat for the desired number of repetitions.
Tip: Tuck the pelvis slightly and keep the ribs down so the glute, not the lower back, gets the squeeze.
Muscles worked
Primary
Glutes · Legs
The glutes drive the leg or hips back and finish the rep, and you should feel a hard squeeze in the working side at the top.
Secondary
- Hamstrings — The hamstrings assist the glutes in extending the hip and get a good stretch on pull-throughs.
Common mistakes
- Arching to get higher — the range ends when the hip is fully extended, not when the spine bends; stop at the point where the glute is squeezed and go no further.
- Rushing the reps — most hip extensions are a squeeze exercise; pause at the top for a count unless the variation is meant to be rhythmic.
- Kicking instead of extending — on kickbacks keep the knee bent at a fixed angle so the glute drives the hip back; if the leg straightens as you lift, it has turned into a leg kick.
- Pull-throughs with a vertical torso — on a cable pull-through you need to hinge far forward with the hips back so the cable stretches the glutes before they fire.
Sets, reps and where it fits
| Goal | Sets × reps | Rest |
|---|---|---|
| Strength | 4–5 × 3–6 | 2–3 min |
| Muscle growth | 3–4 × 6–12 | 90–120 s |
| Endurance | 2–3 × 12–20 | 60 s |
Hip extensions are accessory glute work for after squats, deadlifts or hip thrusts. Cable pull-throughs superset well with cable rows on the same stack, and kickbacks with abduction work.
Variations and alternatives
Similar exercises
Without bodyweight
Frequently asked questions
What muscles does the Bench Hip Extension work?
The Bench Hip Extension primarily works the glutes. It also involves the hamstrings, which assist the movement and stabilise the joints.
Is the Bench Hip Extension good for beginners?
Yes. The Bench Hip Extension is rated beginner: it uses no equipment beyond your bodyweight and the movement is simple to learn. Start light, focus on the full range of motion and add load once every rep looks the same.
What can I do instead of the Bench Hip Extension?
If you cannot do the Bench Hip Extension, try the Kneeling Machine Hip Extension, the Bench Reverse Hyperextension or the Banded Bent Over Hip Extension. Each of them trains the glutes through a similar movement, so you can swap them in without changing the rest of the workout.
How many sets and reps should I do?
It depends on your goal. For the Bench Hip Extension, a sensible starting point is strength: 4–5 × 3–6 with 2–3 min rest; muscle growth: 3–4 × 6–12 with 90–120 s rest; endurance: 2–3 × 12–20 with 60 s rest. Put it early in the session while you are fresh, before isolation work for the same muscles.
Track the Bench Hip Extension in SetGrip
All 1,100+ exercises with animations are in the app. No account, no sign-up — your data stays on your iPhone. Works with Apple Watch.
More exercises
Exercise data and animations are licensed ExerciseDB content used in SetGrip. This page is for general information and is not medical or coaching advice.