Reverse Grip Dumbbell Bench Press
Also known as: reverse grip dumbbell press
In SetGrip: Dumbbell Bench Press (Reverse Grip)
Reverse-grip pressing is far more approachable with dumbbells than with a bar: each hand rotates independently, and there is no fixed bar threatening to roll out of an underhand hold. The supinated position tucks your elbows and shifts emphasis toward the upper chest and triceps, so it substitutes well when the standard pronated press feels rough on your shoulders.
How to do the Reverse Grip Dumbbell Bench Press
- Lie flat on a bench with your feet flat on the ground and your knees bent.
- Hold a dumbbell in each hand with an overhand grip, palms facing towards your feet.
- Extend your arms straight up towards the ceiling, keeping a slight bend in your elbows.
- Slowly lower the dumbbells towards your chest, allowing your elbows to flare out to the sides.
- Pause for a moment at the bottom, then push the dumbbells back up to the starting position.
- Repeat for the desired number of repetitions.
Tip: Squeeze the bar hard and bend it toward your feet to keep the elbows in and the lats tight.
Muscles worked
Primary
Pectorals · Chest
The pecs press the arms together and forward and are worked hardest at the bottom of the rep when the elbows are below the body.
Common mistakes
- Elbows flared to 90 degrees — this puts the shoulder in a poor position at the bottom; tuck the elbows to about 45 to 60 degrees and touch the bar on the lower chest.
- Losing shoulder blade position — the shoulder blades should be pulled back and down before the unrack and stay there; if they roll forward, the chest loses leverage.
- Bouncing off the chest — control the bar to a light touch and pause for a beat before pressing; a bounce hides how much you can actually press.
- Feet dancing around — plant the feet flat and drive them into the floor for the whole set to keep the body tight.
Sets, reps and where it fits
| Goal | Sets × reps | Rest |
|---|---|---|
| Strength | 4–5 × 3–6 | 2–3 min |
| Muscle growth | 3–4 × 6–12 | 90–120 s |
| Endurance | 2–3 × 12–20 | 60 s |
Bench press goes first in a chest or push session when you are strongest. Superset with a dumbbell row on the same bench for a push and pull pair, or follow it with flies for volume.
Variations and alternatives
Similar exercises
Without dumbbell
Easier and harder
Frequently asked questions
What muscles does the Reverse Grip Dumbbell Bench Press work?
The Reverse Grip Dumbbell Bench Press primarily works the pectorals. It also involves the triceps and delts, which assist the movement and stabilise the joints.
Is the Reverse Grip Dumbbell Bench Press good for beginners?
It is rated intermediate, so it suits people who already train regularly. Beginners can still do the Reverse Grip Dumbbell Bench Press with light load and a spotter or coach watching the first few sessions; if it feels awkward, pick an easier variation from the alternatives below first.
What can I do instead of the Reverse Grip Dumbbell Bench Press?
If you cannot do the Reverse Grip Dumbbell Bench Press, try the Barbell Bench Press, the Decline Barbell Bench Press or the Incline Barbell Bench Press. Each of them trains the pectorals through a similar movement, so you can swap them in without changing the rest of the workout.
How many sets and reps should I do?
It depends on your goal. For the Reverse Grip Dumbbell Bench Press, a sensible starting point is strength: 4–5 × 3–6 with 2–3 min rest; muscle growth: 3–4 × 6–12 with 90–120 s rest; endurance: 2–3 × 12–20 with 60 s rest. Put it early in the session while you are fresh, before isolation work for the same muscles.
Track the Reverse Grip Dumbbell Bench Press in SetGrip
All 1,100+ exercises with animations are in the app. No account, no sign-up — your data stays on your iPhone. Works with Apple Watch.
More exercises
Exercise data and animations are licensed ExerciseDB content used in SetGrip. This page is for general information and is not medical or coaching advice.